Most arguments in the sand and gitti business start at the site gate. The customer says the truck is short; the driver says it is full; the dealer is stuck in the middle. Knowing how to measure sand in truck loads properly — and writing that measurement on the bill — is the best way to end these arguments. This guide explains the simple length × width × height method, how to handle uneven and heaped loads, how to convert the result into CFT and brass, and how to keep billing fair for both sides.
How to measure sand in truck loads: length × width × height
Sand and gitti are sold by volume in most local markets, usually in cubic feet (CFT) or brass (1 brass = 100 CFT). To find the volume of a load, measure the inside of the vehicle body:
Volume (CFT) = Inside length (ft) × Inside width (ft) × Height of material (ft)
Three points matter here:
- Measure the inside, not the outside. The body walls and frame can be several inches thick. Outside measurements always over-count.
- Measure the height of the material, not the height of the body. A body that is 3 ft deep but filled to 2.5 ft holds 2.5 ft of sand.
- Use the same tape and the same method every time. Consistency is what keeps both sides calm.
Worked example 1: a tractor trolley
A tractor trolley has an inside length of 10 ft and inside width of 6 ft. The sand is levelled at 2 ft high.
- Volume = 10 × 6 × 2 = 120 CFT
- In brass = 120 ÷ 100 = 1.2 brass
Trolley sizes vary widely between makers and local fabricators, so never assume a trolley "is" one brass. Measure each vehicle once, write its inside dimensions in your records, and check the fill height on every trip.
Worked example 2: an uneven truck load
In real life, sand is rarely level. It is higher in the middle and lower at the sides or ends. The fair approach is to take several height readings and average them.
A truck body is 14 ft long and 7 ft wide inside. You measure the sand height at five points along the centre line: 2.5, 2.75, 3.0, 2.75 and 2.5 ft.
| Step | Calculation | Result |
|---|---|---|
| Average height | (2.5 + 2.75 + 3.0 + 2.75 + 2.5) ÷ 5 | 2.7 ft |
| Volume | 14 × 7 × 2.7 | 264.6 CFT |
| Brass | 264.6 ÷ 100 | about 2.65 brass |
| Cubic metre | 264.6 × 0.02832 | about 7.49 m³ |
Why averaging matters: if someone measured only the highest point (3.0 ft), they would get 14 × 7 × 3.0 = 294 CFT — about 29 CFT, or roughly 11%, more than the averaged figure. At an example rate of ₹50 per CFT, that gap is about ₹1,470 on one truck. Over a month of deliveries, one-sided measuring can cause a lot of bad feeling, whichever side it favours.
For a more accurate average, take readings in a grid — for example, three across the width at three points along the length — and average all nine.
Handling feet and inches
Tape measures show feet and inches. Convert inches to decimal feet before multiplying:
| Inches | Decimal feet |
|---|---|
| 3 in | 0.25 ft |
| 6 in | 0.5 ft |
| 9 in | 0.75 ft |
Example: a body 10 ft 6 in long, 6 ft 3 in wide, with sand at 2 ft 9 in.
- 10.5 × 6.25 × 2.75 = about 180.5 CFT ≈ 1.80 brass
A common mistake is to write 10 ft 6 in as "10.6 ft". That is wrong — 6 inches is half a foot, so it is 10.5 ft. Train staff on this; it causes many small errors.
Heaped loads and gitti
When material is heaped above the body sides, the simple box formula under-counts the heap. There is no single correct formula for an irregular heap, so many dealers use one of these practical approaches:
- Level the load before measuring. Spread the material evenly within the body, then measure. This is the simplest and fairest method.
- Agree a body-level rule. Fill to the top edge of the body only, so the volume is the inside box. This is easy to check at the site.
- Average several heights, as shown above, including points on the heap.
For gitti (stone aggregate), the same L × W × H method applies. Note the size — 10 mm, 20 mm, 40 mm — on the bill, because customers order by size and the same volume of different sizes is not interchangeable.
Volume vs weight: why the two do not match
Some customers or projects want sand by weight (tonnes from a weighbridge), others by volume (CFT or brass). These are not the same thing, and you cannot convert one to the other with a fixed number.
The reasons:
- Moisture. Wet sand weighs more. Damp sand can also take up more volume than dry sand — engineers call this bulking. Lab guidance notes that bulking is greatest at a moisture content of roughly 4–6% and falls back as sand becomes fully saturated.
- Settling. Sand loaded loosely settles during the journey, so a load measured at the loading point may look lower at the site.
- Grain size and type. River sand, M-sand and different gitti sizes all pack differently.
Practical rules:
- Decide with the customer before delivery whether you are billing by volume or by weight.
- If by weight, attach the weighbridge (dharam kanta) slip number to the bill.
- If by volume, measure and note it at loading, and allow the customer to check at the site.
- Do not mix the two on one order unless both sides have agreed the method in writing.
Preventing measurement disputes
A few habits stop most arguments before they start:
- Record vehicle dimensions once. Keep a list of every regular truck and trolley with its inside length, width and depth.
- Write the measurement on the challan. Length, width, average height and total CFT — not just "1 trolley".
- Photograph the load. A quick photo at loading, with the tape visible, settles most doubts.
- Invite the customer or site supervisor to check. Transparency costs you nothing if the load is honest.
- Settle small differences quickly. A 2–3 CFT gap is not worth losing a regular contractor over.
- Use the same rules for every customer. Word spreads fast in a small town.
Billing sand and gitti correctly
Once the volume is agreed, the bill should show it clearly: material, size, quantity with unit (CFT or brass), rate per that unit, vehicle number and site. Natural sand (HSN 2505) and stone aggregate / gitti (HSN 2517) are both taxed at 5% GST. For other items, see our GST rates page. GST rates and rules change; check the latest CBIC notification or ask your CA before filing.
If a single delivery's value crosses the e-way bill limit, you may need one. The limit is generally ₹50,000, but some states set different intra-state limits — check your state's limit. Our guide on making an e-way bill covers the steps. Freight and trip costing are covered in our guide on transport and freight costing.
MaterialBill's delivery challan records the vehicle, site and freight for every trip, and multi-unit billing lets you sell the same sand item in CFT or brass, with the rate converting automatically. Each bill can be shared with the customer on WhatsApp the moment the truck leaves.
Frequently asked questions
How do I measure sand in a truck load?
Measure the inside length and width of the body and the average height of the sand, all in feet. Multiply them to get cubic feet (CFT). Divide by 100 to get brass.
How many CFT of sand is in a tractor trolley?
It depends on the trolley. Trolley sizes vary by maker, so measure the inside of each one. For example, a trolley 10 ft × 6 ft filled level to 2 ft holds 120 CFT, or 1.2 brass.
How many cubic feet are in one brass of sand?
One brass is 100 CFT, which is about 2.83 cubic metres.
Why does the sand look less when it reaches the site?
Loose sand settles during transport, and moisture changes its volume. Measuring at loading, noting it on the challan and photographing the load helps avoid disputes.
Should I bill sand by weight or by volume?
Either can work, but agree on one method with the customer before delivery. If you bill by weight, note the weighbridge slip number on the bill. Do not convert between weight and volume using a fixed factor.
Fair measuring and clear bills keep contractors coming back. If you want every sand and gitti trip recorded with vehicle, size, CFT and brass on one challan, you can start free with MaterialBill's sand supplier billing software.