Steel is bought and sold by weight, but customers think in pieces. A mistri asks for "50 pieces of 12mm", the company invoice says "4.2 MT", and your counter has to connect the two. A reliable TMT bar weight chart is the bridge. This guide gives you the standard weights from 8mm to 32mm, the simple formula behind them, what IS 1786 allows as weight variation, and how to bill without arguments.
TMT bar weight chart: 8mm to 32mm
The figures below are the nominal (standard) mass per metre under IS 1786, the Indian Standard for high strength deformed steel bars. The "per bar" column assumes the standard 12 m length.
| Bar size | Weight per metre (kg/m) | Weight per 12 m bar (kg) | Bars per tonne (approx.) |
|---|---|---|---|
| 8 mm | 0.395 | 4.74 | 211 |
| 10 mm | 0.617 | 7.40 | 135 |
| 12 mm | 0.888 | 10.66 | 94 |
| 16 mm | 1.58 | 18.96 | 53 |
| 20 mm | 2.47 | 29.64 | 34 |
| 25 mm | 3.85 | 46.20 | 22 |
| 32 mm | 6.31 | 75.72 | 13 |
How the columns are worked out: per bar = kg/m × 12. Bars per tonne = 1,000 ÷ weight per bar, rounded. Actual bars per tonne will differ a little because real bars are not exactly at nominal mass.
Keep this table at the counter. A quick check of 12mm rod weight, for instance, tells you a bundle that "should be 50 kg" is almost five bars, not four or six.
The D²/162 formula and where it comes from
Every number in the chart can be worked out with one formula:
Weight (kg per metre) = D² ÷ 162, where D is the bar diameter in millimetres.
Example for 16mm: 16 × 16 = 256. 256 ÷ 162 = 1.58 kg/m.
Why 162? Steel weighs about 7,850 kg per cubic metre. A bar's cross-section area is π × D² ÷ 4. Multiply area by one metre of length and by steel density, convert millimetres to metres, and the constant works out to roughly 162. You don't need to remember the derivation, only that the formula assumes a plain round bar at nominal size. The ribs on a TMT bar are already accounted for in the "nominal mass" the standard uses.
For sizes not in the chart, the formula is accurate enough for estimates. For example, 28mm gives 784 ÷ 162 = 4.84 kg/m.
Weight per bundle: why the count varies
Customers often ask "how many bars in a bundle?" There is no single answer you should promise.
IS 1786 defines a bundle simply as a number of lengths properly bound together, and requires each bundle to carry a tag showing the cast or lot number, grade and size. It does not fix how many bars go in a bundle. Many mills follow their own bundling norms, and the count depends on size. Smaller sizes like 8mm and 10mm come with more bars per bundle; 25mm and 32mm bars are often dispatched as single bars or very small bundles.
The practical rule: count the bars in each bundle when the truck arrives, and record it by size. Don't assume the count from one company or one lot applies to the next. Once you know the count, the bundle weight is just count × weight per bar.
Example: if your 10mm bundles arrive with 8 bars each, the nominal bundle weight is 8 × 7.40 = 59.2 kg.
How much weight variation IS 1786 allows
Real bars are never exactly at nominal weight. IS 1786 (Table 2, tolerances on nominal mass) sets limits on how far they can be off:
| Bar size | Batch tolerance | Individual sample tolerance |
|---|---|---|
| Up to and including 10 mm | ±7% | −8% |
| Over 10 mm up to 16 mm | ±5% | −6% |
| Over 16 mm | ±3% | −4% |
A few points worth understanding:
- Batch means a quantity of bars of the same size and grade. The batch tolerance applies to the average across a batch sample.
- For an individual sample, the standard sets only a minus limit. No plus limit is specified for individual bars.
- Samples are at least 0.5 m long, so this is a lab-style check, not something you do by weighing one bar on a counter scale.
What this means for a dealer: a lot of 12mm bars weighing 3–4% less than the chart is still within the batch limit. If a lot of 12mm bars averages well beyond 5% light, raise it with your supplier and keep the weighbridge record. This is also why people talk about "rolling margin": bars rolled slightly under nominal mass give a buyer more length per tonne but less steel per metre.
Engineers and site supervisors usually specify how steel should be checked on their projects. When a customer has a quality concern, point them to the mill's test certificate and their engineer rather than settling it at the counter.
Billing sariya by weight vs by piece
Under GST, TMT bars fall under HSN 7214 (or 7213 for bars in coils) at 18%. The tax doesn't change with how you bill, but the quantity on your invoice does. There are three common ways to sell.
1. Actual weight (weighbridge or scale). You weigh the material and bill the actual kg. This is the fairest method for large loads. Note the kanta slip number on the bill.
2. Theoretical weight (pieces × chart weight). You count pieces and convert using the chart. Fast at the counter, and easy for the customer to check. The risk: if the bars are lighter than nominal, you bill more steel than you actually hand over, and that can lead to complaints.
3. Per piece. Some retail counters quote a price per bar. This is simple, but your margin moves every time the actual weight of a lot changes.
Worked example: billing 50 pieces of 12mm
The rate below is an example only; steel rates change daily.
- Rate (example): ₹58 per kg, excluding GST
- Theoretical weight: 50 × 10.66 kg = 533 kg
- Actual weight on scale: 517 kg (3% under nominal, within the batch tolerance)
| Method | Billed weight | Taxable value | GST 18% | Total |
|---|---|---|---|---|
| Theoretical | 533 kg | ₹30,914 | ₹5,564.52 | ₹36,478.52 |
| Actual | 517 kg | ₹29,986 | ₹5,397.48 | ₹35,383.48 |
The difference is over ₹1,000 on one small order. Whatever method you use, agree it with the customer before loading, and print it on the bill, for example "50 pcs 12mm, actual weight 517 kg". Our guide on sariya rate and billing covers daily rate updates and party-wise rates in more detail.
Tracking steel stock by size
Weight-based steel is hard to count if your books only say "TMT – 12 tonnes". You need stock by size, and ideally both in pieces and kg.
- Record purchases in tonnes as the mill invoices them.
- Sell in kg, pieces or bundles as customers ask.
- Keep separate items for each diameter (and grade, if you stock more than one).
- Reconcile the theoretical stock with the physical count every month, since small weight differences pile up.
MaterialBill supports multi-unit billing so you can buy in tonnes and sell in kg or pieces with conversions set per item, and keeps size-wise stock from 8mm to 32mm. More features for steel dealers are on our sariya and steel billing software page. For general methods to count and reconcile stock, see stock management.
Frequently asked questions
What is the weight of a 12mm TMT bar?
A 12mm bar has a nominal weight of 0.888 kg per metre, so a standard 12 m bar weighs about 10.66 kg. Actual weight can vary within the IS 1786 tolerance.
How do I calculate sariya weight per metre?
Square the diameter in mm and divide by 162. For 10mm: 100 ÷ 162 = 0.617 kg/m. Multiply by the length in metres for the total.
How many bars are in a bundle of 8mm TMT?
It depends on the mill and lot. IS 1786 does not fix the count. Count the bars when stock arrives and record it by size.
Is it legal to bill steel at theoretical weight?
Billing method is a commercial agreement with your buyer. Whatever you choose, show the weight and method clearly on the invoice and make sure the buyer agrees to it.
My 16mm bars weigh 4% less than the chart. Is that a defect?
For a batch of 16mm bars, IS 1786 allows ±5%, so 4% light on the batch average is within the limit. For larger variations, raise it with your supplier and refer to the mill's test certificate.
The chart only helps if your bills follow it. If you want steel rates, sizes and kg-to-piece conversions handled in one place, you can start free with MaterialBill and set up your sariya items in a few minutes.