Home › Blog › Product knowledge and calculators › How Many Bricks in a Wall

How Many Bricks in a Wall? Brick Calculation for Walls (With Examples)

Quick answer

About 500 modular bricks or 434 non-modular bricks go into 1 m³ of brickwork, before wastage. Add about 5% for wastage.

Wall Modular bricks per sq ft Non-modular bricks per sq ft
4.5 inch ≈ 4.6 ≈ 4.8
9 inch ≈ 9.3 ≈ 9.7
In this article
  1. Start with the brick size
  2. How many bricks in a wall per square foot: the face-area method
  3. Worked example 1: a 9-inch wall with a door
  4. Wastage: how much extra to add
  5. Mortar, plaster and things customers forget
  6. Selling bricks: billing and GST
  7. Frequently asked questions

"Bhaiya, how many bricks in a wall of 12 by 10 feet?" Every brick supplier hears this question daily. Getting it right matters: quote too few and the customer comes back angry halfway through the job; quote too many and they feel cheated. This guide shows a simple, honest brick calculation method — based on brick size, wall thickness and wall area — with worked examples for 4.5-inch and 9-inch walls, deductions for doors and windows, and a sensible wastage allowance.

Start with the brick size

Every brick calculation begins with the size of the brick you actually sell. IS 1077, the Indian Standard for common burnt clay bricks, gives two families of sizes:

Type (IS 1077) Actual size (L × W × H) Size with 10 mm mortar joint
Modular brick 190 × 90 × 90 mm 200 × 100 × 100 mm
Non-modular brick 230 × 110 × 70 mm 240 × 120 × 80 mm

The "size with mortar" is what counts for the calculation, because each brick takes up its own space plus about 10 mm of mortar on one end and one bed.

An important practical point: many local kilns, especially traditional bhattas, make bricks that do not match either IS size exactly. Before you quote, measure a few bricks from your own stock with a tape — length, width and height — and use those numbers. The method below works for any size.

The quick rule: bricks per cubic metre

With modular bricks, the size with mortar is 0.2 × 0.1 × 0.1 m = 0.002 m³. So:

1 ÷ 0.002 = 500 bricks per cubic metre (modular, rough rule)

For non-modular bricks: 0.24 × 0.12 × 0.08 = 0.002304 m³, which gives about 434 bricks per cubic metre.

The 500-per-m³ figure is widely used for quick estimates. It is a rule of thumb based on nominal size, so for quoting a specific wall, the face-area method in the next section is easier and closer.

How many bricks in a wall per square foot: the face-area method

Most customers give you wall length and height, not volume. So it is easier to work in area.

Look at the face of the wall. Each brick, laid lengthwise, shows its length × height (with mortar) on the face:

A one-brick (full) wall is two bricks thick, so it needs double.

Since 1 m² = 10.764 sq ft, here is the full table:

Wall type Modular brick (190 mm) Non-modular brick (230 mm)
Half-brick wall ("4.5-inch"), per m² 50 about 52
Half-brick wall, per sq ft about 4.6 about 4.8
One-brick wall ("9-inch"), per m² 100 about 104
One-brick wall, per sq ft about 9.3 about 9.7

These figures do not include wastage. We add that at the end.

A note on names: in the trade, "9-inch wall" and "4.5-inch wall" come from the old 9-inch brick. With modular bricks, the actual wall is about 190 mm or 90 mm thick, but people still use the same names.

Worked example 1: a 9-inch wall with a door

A customer is building a 9-inch (one-brick) wall, 12 ft long and 10 ft high, with one door opening of 3 ft × 7 ft. He uses non-modular bricks.

Step 1 — gross wall area 12 × 10 = 120 sq ft

Step 2 — deduct openings Door: 3 × 7 = 21 sq ft Net area = 120 − 21 = 99 sq ft

Step 3 — multiply by bricks per sq ft 99 × 9.677 = about 958 bricks

Step 4 — add wastage (5%) 958 × 1.05 = about 1,006 bricks

So quote about 1,000 bricks. If he were using modular bricks instead, the figure would be 99 × 9.29 = about 920, or about 966 with 5% wastage.

Worked example 2: a 4.5-inch partition wall

A 4.5-inch (half-brick) partition, 10 ft long and 8 ft high, no openings, using non-modular bricks.

With modular bricks: 80 × 4.65 = about 372, or about 390 with wastage.

Worked example 3: four walls of a room

A room is 12 ft × 10 ft, with walls 10 ft high, 9-inch thick, modular bricks. It has one door (3 × 7 ft) and two windows (4 × 4 ft each).

Step Calculation Result
Perimeter 2 × (12 + 10) 44 ft
Gross wall area 44 × 10 440 sq ft
Door 3 × 7 − 21 sq ft
Windows 2 × 4 × 4 − 32 sq ft
Net area 440 − 21 − 32 387 sq ft
Bricks (9.29 per sq ft) 387 × 9.29 about 3,595
With 5% wastage 3,595 × 1.05 about 3,775

This is a simplified estimate. In a real room, the corners overlap, so measuring along the outside of every wall slightly over-counts. For a quote that is fine; for a large building, the engineer or contractor will work from the drawing.

Wastage: how much extra to add

Bricks break in loading, unloading, cutting and handling. Some arrive with chipped corners or are under-burnt. A 5% allowance is a common rule of thumb for good-quality bricks and careful handling. Many suppliers suggest more for:

Use your own experience with each batch and each customer. Telling the customer up front that the figure includes a wastage margin builds trust.

Mortar, plaster and things customers forget

Bricks are only part of the job. When a customer asks for a wall quote, remind them about:

For walls that carry loads, the engineer's design governs the brick class, wall thickness and mortar mix. Your calculation is for quoting and supply only.

Selling bricks: billing and GST

Bricks are usually sold per thousand or per piece, with delivery charged by trip. Keep your bills clear: number of bricks, rate, vehicle, site and freight.

GST on bricks has special rules. Clay bricks and fly-ash bricks are taxed at 12% with input tax credit, or 6% without ITC, under the special brick scheme, which the Finance Ministry confirmed is unchanged after September 2025, while sand-lime bricks were cut from 12% to 5% under GST 2.0. Because the scheme conditions and the correct HSN depend on your registration and the exact product, check the details with your CA before billing. Our GST rates page has the current list. GST rates and rules change; check the latest CBIC notification or ask your CA before filing.

MaterialBill helps brick suppliers bill per piece or per thousand and keep stock for each type of brick. Delivery challans record the vehicle, site and freight for each trip, and the quotation feature turns your brick estimate into a written quote the customer can approve on WhatsApp. If brick buyers often take material on credit, see our guide on keeping udhaar accounts.

Frequently asked questions

How many bricks are there in 1 cubic metre?

With IS 1077 modular bricks (190 × 90 × 90 mm, or 200 × 100 × 100 mm with mortar), the rough rule is 500 bricks per m³. With non-modular bricks (230 × 110 × 70 mm), it is about 434. Local brick sizes vary, so measure your own.

How many bricks are needed per square foot of wall?

For a 4.5-inch wall, about 4.6 (modular) to 4.8 (non-modular) bricks per sq ft. For a 9-inch wall, about 9.3 to 9.7 bricks per sq ft. Add wastage on top.

How much wastage should I add to a brick quote?

About 5% is a common rule for good bricks and careful handling. Add more for long transport, many cuts, or bricks from an unfamiliar kiln.

Should I deduct doors and windows?

Yes. Work out the area of each opening and subtract it from the gross wall area before multiplying by bricks per sq ft.

Is this calculation enough for a load-bearing wall?

It is fine for quoting and supply. The brick class, wall thickness and mortar mix for a load-bearing wall must come from the site engineer's design.

Fast, clear quotes win brick orders. If you want to send brick estimates on WhatsApp and bill trip by trip with challans, you can start free with MaterialBill's bricks shop billing software.

Related articles

TMT Bar Weight Chart TMT Bar Grades Fe415, Fe500, Fe500D and Fe550D OPC vs PPC Cement (and PSC) Cement Shelf Life and Storage Cement Sand Aggregate Calculation for 1 Cubic Metre of Concrete Building Material Unit Conversions All blog posts

Start Free Today

Set up in two minutes. No card required. Leave whenever you like — your data always stays yours.